====================== Interact with errors ====================== There are a couple of things that you can do with Flycheck errors in a buffer: * You can navigate to errors, and go to the next or previous error. * You can display errors to read their error messages. * You can put error messages and IDs into the kill ring. This section documents the corresponding commands and their customisation options. Navigate errors =============== By default Flycheck hooks into Emacs’ standard error navigation on :kbd:`M-g n` (`next-error`) and :kbd:`M-g p` (`previous-error`). When :mode:`flycheck` is enabled these commands will jump to the next and previous Flycheck error respectively. See :infonode:`(emacs)Compilation Mode` for more information about these commands. This way you don’t need to learn special keybindings to navigate Flycheck errors; navigation should just work out of the box. .. note:: Visible compilation buffers such as buffers from ``M-x compile``, ``M-x grep``, etc. still take *precedence* over Flycheck’s errors. The exact behaviour of these error navigation features is very context-dependent and can be very confusing at times so you can disable this integration: .. defcustom:: flycheck-standard-error-navigation Whether to integrate Flycheck errors into Emacs’ standard error navigation. Defaults to ``t``, set to ``nil`` to disable. .. important:: When changing the value you must disable :mode:`flycheck` and enable it again for the change to take effect in any buffers where :mode:`flycheck` is enabled. Flycheck provides an independent set of navigation commands which will always navigate Flycheck errors in the current buffer, regardless of visible compilation buffers and `flycheck-standard-error-navigation`: .. define-key:: C-c ! n M-x flycheck-next-error Jump to the next error. With prefix argument jump forwards by as many errors as specified by the prefix argument, e.g. :kbd:`M-3 C-c ! n` will move to the 3rd error from the current point. With negative prefix argument move to previous errors instead. Signal an error if there are no more Flycheck errors. .. define-key:: C-c ! p M-x flycheck-previous-error Jump to the previous Flycheck error. With prefix argument jump backwards by as many errors as specified by the prefix argument, e.g. :kbd:`M-3 C-c ! p` will move to the 3rd error before the current point. With negative prefix argument move to next errors instead. Signal an error if there are no more Flycheck errors. .. define-key:: M-x flycheck-first-error Jump to the first Flycheck error. With prefix argument, jump forwards to by as many errors as specified by the prefix argument, e.g. :kbd:`M-3 M-x flycheck-first-error` moves to the 3rd error from the beginning of the buffer. With negative prefix argument move to the last error instead. By default error navigation jumps to all errors but you can choose to skip over errors with low levels: .. defcustom:: flycheck-navigation-minimum-level The minimum levels of errors to consider for navigation. If set to an error level only navigate to errors whose level is as least as severe as this one. If ``nil`` navigate to all errors. Display errors ============== Whenever you move point to an error location Flycheck automatically displays all Flycheck errors at point after a short delay which you can customise: .. defcustom:: flycheck-display-errors-delay The number of seconds to wait before displaying the error at point. Floating point numbers can express fractions of seconds. By default Flycheck shows the error messages in the minibuffer or in a separate buffer if the minibuffer is too small to hold the whole error message but this behaviour is entirely customisable: .. defcustom:: flycheck-display-errors-function A function to display errors. The function is given the list of Flycheck errors to display as sole argument and shall display these errors to the user in some way. Flycheck provides two built-in functions for this option: .. defun:: flycheck-display-error-messages errors flycheck-display-error-messages-unless-error-list errors Show error messages and IDs in the echo area or in a separate buffer if the echo area is too small (using `display-message-or-buffer` which see). The latter only displays errors when the :ref:`error list ` is not visible. To enable it add the following to your :term:`init file`: .. code-block:: elisp (setq flycheck-display-errors-function #'flycheck-display-error-messages-unless-error-list) .. seealso:: :flyc:`flycheck-pos-tip` A Flycheck extension to display errors in a GUI popup. Additionally Flycheck shows errors in a GUI tooltip whenever you hover an error location with the mouse pointer. By default the tooltip contains the messages and IDs of all errors under the pointer, but the contents are customisable: .. defcustom:: flycheck-help-echo-function A function to create the contents of the tooltip. The function is given a list of Flycheck errors to display as sole argument and shall return a single string to use as the contents of the tooltip. Explain errors ============== Flycheck also has the ability to display explanations for errors, provided the error checker is capable of producing these explanations. Currently, only the `rust` and `rust-cargo` checkers produce explanations. .. define-key:: C-c ! e M-x flycheck-explain-error-at-point Display an explanation for the first explainable error at point. Kill errors =========== You can put errors into the kill ring with `C-c ! w`: .. define-key:: C-c ! w M-x flycheck-copy-errors-as-kill Copy all messages of the errors at point into the kill ring. .. define-key:: C-u C-c ! w C-u M-x flycheck-copy-errors-as-kill Like `C-c ! w` but with error IDs. .. define-key:: M-0 C-c ! w M-0 M-x flycheck-copy-errors-as-kill Like `C-c ! w` but do not copy the error messages but only the error IDs.